China factory Steering Bearing Ball Bearing Steering Wheel Bearing Steering Gear System Vtaa19z-2 Vtaa19z-1 Vtaa19z-4 Vbt15z-2 Vbt17z-2 Vbt17z-3 Vbt17z-4 Vbt20z-1 with Good quality

Product Description

We has more experience to make a design of steering bearing system.
especially in Auto parts line also in remote steering bearing.So we welcome customer to make a inquiry into us about further information
about steering wheel bearings.

The entire basic steering assembly is called a Triple Tree, Triple Clamp, Steering Head, Steering Head Yoke, or Steering Stem. Up until around 1985 most, but not all, loose ball bearings for their steering races. These bearings have upper and lower outer races that are a tight press fit in the frame and a lower inner race  that is press fitted to the steering stem. The upper inner race is a loose fit.

Most late model steering gearbox use either tapered roller bearings or caged ball bearings. Caged ball bearings and tapered roller bearings are lubed the same way and are much easier to handle. Even with the front wheel removed that front end felt like it weighed a thousand pounds! I slid everything together and “Ping” 1 lousy ball bearing popped out.
 

 

BEARING NO. d D B
ACS0304   40 11
ACS0304-2   35 10.5
ACS0404   41 12
ACS040412   43 12.5
ACS040514   47 14.3
ACS0405D-2   52 15
ACS0405J-4 19.5 47 11
ACS0405J-2 19.5 47 13.5
ACS0506 25 62 18
ACS0506FX 25 62 19
BT18Z-1B1 18.72 38 10
BT19Z-1A 22 47 16
BT25-4 25 62 18.7
BT30-5A 30 72 21.2
C4TZ3552A 37.8 54 12
C4TZ3553A 37.8 59 12
C6TZ3552A   45.95 11
C6TZ3553A   49.15 11
CB01 19.5 58.85 17.9
E15 15 35 8
E20 20 47 12
L17 17 40 10
M307487   32 10.11
S9072   60 6
VBT15Z-2   35 11
VBT17Z-2   38 10.9
VBT17Z-3   40 11
VBT17Z-4   40 10.9
VBT20Z-1   44 12
VBT21Z-1   42 13.5
VTAA19Z-1   41 11.5
VTAA19Z-4   41 12
128602   48 13.5
128702   44 12
128802   38.1 11.1
128202K   35 10.5
15BCW02 15 35 11
15BSW02   35 10
15BSW06B 15 35.2 12
17VBSW02   42 13
18BSC01 18.5 40 10
20BSW01 20 52 15
20BSW04A 20 52 17
28BSC01 28.5 43 11
3401R-100   52 15
509043 26.5 57 15
569304 20 47 16
567404-3 20 52 16
567405-1 25 60 18
561305-1 25 60 18
569306 30 60 18
5666683 27.5 38.1 7.9
5666693 20 34.2 7.9
5666683/93 19 38.1 7.9
9168304 20 47 16
BEARING NO. d D B
ACS0304   40 11
ACS0304-2   35 10.5
ACS0404   41 12
ACS040412   43 12.5
ACS040514   47 14.3
ACS0405D-2   52 15
ACS0405J-4 19.5 47 11
ACS0405J-2 19.5 47 13.5
ACS0506 25 62 18
ACS0506FX 25 62 19
BT18Z-1B1 18.72 38 10
BT19Z-1A 22 47 16
BT25-4 25 62 18.7
BT30-5A 30 72 21.2
C4TZ3552A 37.8 54 12
C4TZ3553A 37.8 59 12
C6TZ3552A   45.95 11
C6TZ3553A   49.15 11
CB01 19.5 58.85 17.9
E15 15 35 8
E20 20 47 12
L17 17 40 10
M307487   32 10.11
S9072   60 6
VBT15Z-2   35 11
VBT17Z-2   38 10.9
VBT17Z-3   40 11
VBT17Z-4   40 10.9
VBT20Z-1   44 12
VBT21Z-1   42 13.5
VTAA19Z-1   41 11.5
VTAA19Z-4   41 12
128602   48 13.5
128702   44 12
128802   38.1 11.1
128202K   35 10.5
15BCW02 15 35 11
15BSW02   35 10
15BSW06B 15 35.2 12
17VBSW02   42 13
18BSC01 18.5 40 10
20BSW01 20 52 15
20BSW04A 20 52 17
28BSC01 28.5 43 11
3401R-100   52 15
509043 26.5 57 15
569304 20 47 16
567404-3 20 52 16
567405-1 25 60 18
561305-1 25 60 18
569306 30 60 18
5666683 27.5 38.1 7.9
5666693 20 34.2 7.9
5666683/93 19 38.1 7.9
9168304 20 47 16

Types of Bevel Gears

Bevel Gears are used in a number of industries. They are used in wheeled excavators, dredges, conveyor belts, mill actuators, and rail transmissions. A bevel gear’s spiral or angled bevel can make it suitable for confined spaces. It is also used in robotics and vertical supports of rolling mills. You can use bevel gears in food processing processes. For more information on bevel gears, read on.
gear

Spiral bevel gear

Spiral bevel gears are used to transmit power between two shafts in a 90-degree orientation. They have curved or oblique teeth and can be fabricated from various metals. Bestagear is one manufacturer specializing in medium to large spiral bevel gears. They are used in the mining, metallurgical, marine, and oil fields. Spiral bevel gears are usually made from steel, aluminum, or phenolic materials.
Spiral bevel gears have many advantages. Their mesh teeth create a less abrupt force transfer. They are incredibly durable and are designed to last a long time. They are also less expensive than other right-angle gears. They also tend to last longer, because they are manufactured in pairs. The spiral bevel gear also reduces noise and vibration from its counterparts. Therefore, if you are in need of a new gear set, spiral bevel gears are the right choice.
The contact between spiral bevel gear teeth occurs along the surface of the gear tooth. The contact follows the Hertz theory of elastic contact. This principle holds for small significant dimensions of the contact area and small relative radii of curvature of the surfaces. In this case, strains and friction are negligible. A spiral bevel gear is a common example of an inverted helical gear. This gear is commonly used in mining equipment.
Spiral bevel gears also have a backlash-absorbing feature. This feature helps secure the thickness of the oil film on the gear surface. The shaft axis, mounting distance, and angle errors all affect the tooth contact on a spiral bevel gear. Adjusting backlash helps to correct these problems. The tolerances shown above are common for bevel gears. In some cases, manufacturers make slight design changes late in the production process, which minimizes the risk to OEMs.

Straight bevel gear

Straight bevel gears are among the easiest types of gears to manufacture. The earliest method used to manufacture straight bevel gears was to use a planer equipped with an indexing head. However, improvements have been made in manufacturing methods after the introduction of the Revacycle system and the Coniflex. The latest technology allows for even more precise manufacturing. Both of these manufacturing methods are used by CZPT. Here are some examples of straight bevel gear manufacturing.
A straight bevel gear is manufactured using two kinds of bevel surfaces, namely, the Gleason method and the Klingelnberg method. Among the two, the Gleason method is the most common. Unlike other types of gear, the CZPT method is not a universal standard. The Gleason system has higher quality gears, since its adoption of tooth crowning is the most effective way to make gears that tolerate even small assembly errors. It also eliminates the stress concentration in the bevelled edges of the teeth.
The gear’s composition depends on the application. When durability is required, a gear is made of cast iron. The pinion is usually three times harder than the gear, which helps balance wear. Other materials, such as carbon steel, are cheaper, but are less resistant to corrosion. Inertia is another critical factor to consider, since heavier gears are more difficult to reverse and stop. Precision requirements may include the gear pitch and diameter, as well as the pressure angle.
Involute geometry of a straight bevel gear is often computed by varying the surface’s normal to the surface. Involute geometry is computed by incorporating the surface coordinates and the theoretical tooth thickness. Using the CMM, the spherical involute surface can be used to determine tooth contact patterns. This method is useful when a roll tester tooling is unavailable, because it can predict the teeth’ contact pattern.
gear

Hypoid bevel gear

Hypoid bevel gears are an efficient and versatile speed reduction solution. Their compact size, high efficiency, low noise and heat generation, and long life make them a popular choice in the power transmission and motion control industries. The following are some of the benefits of hypoid gearing and why you should use it. Listed below are some of the key misperceptions and false assumptions of this gear type. These assumptions may seem counterintuitive at first, but will help you understand what this gear is all about.
The basic concept of hypoid gears is that they use two non-intersecting shafts. The smaller gear shaft is offset from the larger gear shaft, allowing them to mesh without interference and support each other securely. The resulting torque transfer is improved when compared to conventional gear sets. A hypoid bevel gear is used to drive the rear axle of an automobile. It increases the flexibility of machine design and allows the axes to be freely adjusted.
In the first case, the mesh of the two bodies is obtained by fitting the hyperboloidal cutter to the desired gear. Its geometric properties, orientation, and position determine the desired gear. The latter is used if the desired gear is noise-free or is required to reduce vibrations. A hyperboloidal cutter, on the other hand, meshes with two toothed bodies. It is the most efficient option for modeling hypoid gears with noise concerns.
The main difference between hypoid and spiral bevel gears is that the hypoid bevel gear has a larger diameter than its counterparts. They are usually found in 1:1 and 2:1 applications, but some manufacturers also provide higher ratios. A hypoid gearbox can achieve speeds of three thousand rpm. This makes it the preferred choice in a variety of applications. So, if you’re looking for a gearbox with a high efficiency, this is the gear for you.

Addendum and dedendum angles

The addendum and dedendum angles of a bevel gear are used to describe the shape and depth of the teeth of the gear. Each tooth of the gear has a slightly tapered surface that changes in depth. These angles are defined by their addendum and dedendum distances. Addendum angle is the distance between the top land and the bottom surface of the teeth, while dedendum angle is the distance between the pitch surface and the bottom surface of the teeth.
The pitch angle is the angle formed by the apex point of the gear’s pitch cone with the pitch line of the gear shaft. The dedendum angle, on the other hand, is the depth of the tooth space below the pitch line. Both angles are used to measure the shape of a bevel gear. The addendum and dedendum angles are important for gear design.
The dedendum and addendum angles of a bevel gear are determined by the base contact ratio (Mc) of the two gears. The involute curve is not allowed to extend within the base diameter of the bevel gear. The base diameter is also a critical measurement for the design of a gear. It is possible to reduce the involute curve to match the involute curve, but it must be tangential to the involute curve.
The most common application of a bevel gear is the automotive differential. They are used in many types of vehicles, including cars, trucks, and even construction equipment. They are also used in the marine industry and aviation. Aside from these two common uses, there are many other uses for bevel gears. And they are still growing in popularity. But they’re a valuable part of automotive and industrial gearing systems.
gear

Applications of bevel gears

Bevel gears are used in a variety of applications. They are made of various materials depending on their weight, load, and application. For high-load applications, ferrous metals such as grey cast iron are used. These materials have excellent wear resistance and are inexpensive. For lower-weight applications, steel or non-metals such as plastics are used. Some bevel gear materials are considered noiseless. Here are some of their most common uses.
Straight bevel gears are the easiest to manufacture. The earliest method of manufacturing them was with a planer with an indexing head. Modern manufacturing methods introduced the Revacycle and Coniflex systems. For industrial gear manufacturing, the CZPT uses the Revacycle system. However, there are many types of bevel gears. This guide will help you choose the right material for your next project. These materials can withstand high rotational speeds and are very strong.
Bevel gears are most common in automotive and industrial machinery. They connect the driveshaft to the wheels. Some even have a 45-degree bevel. These gears can be placed on a bevel surface and be tested for their transmission capabilities. They are also used in testing applications to ensure proper motion transmission. They can reduce the speed of straight shafts. Bevel gears can be used in many industries, from marine to aviation.
The simplest type of bevel gear is the miter gear, which has a 1:1 ratio. It is used to change the axis of rotation. The shafts of angular miter bevel gears can intersect at any angle, from 45 degrees to 120 degrees. The teeth on the bevel gear can be straight, spiral, or Zerol. And as with the rack and pinion gears, there are different types of bevel gears.